Tell us the diameter and what you fill. One line starts a quote.

Quick message

Leave a contact. We reply in writing.

Two fields are enough. If you only know the end product, say that — we will ask for the rest once.

Reply within one working day · GMT+8

Prefer to write directly? +86 138 0518 4203

Can bodies held on the print mandrels during decoration

Applications · Automotive

Automotive is where the formulation is the whole specification.

Brake cleaner, carburettor cleaner, penetrating lubricant, tyre shine, underbody coating, gasket remover. Almost nothing in this sector is read for its beauty; the product is judged by whether it works in the first ten seconds and whether the can is still usable a year later in a workshop that freezes in winter. That moves the entire specification onto the lining and the valve, and away from the print.

De 46–66 mm · aggressive solvents · long spray duration

Why are automotive fills harder on the can than anything else?

Because the solvent list is brutal. Acetone, toluene, xylene, heptane, naphtha and chlorinated blends all appear in this sector, and several of them will pass through a polymer lining given time and temperature. The failure mode is not a dramatic rupture: it is a lining that softens, lifts at the base, and lets the formulation reach bare aluminium, after which the can fails from the inside. A workshop shelf that reaches 40 °C in summer accelerates it.

This is the sector where we are least willing to recommend a lining from a formulation name alone. A product called “brake cleaner” can be an acetone blend, a heptane blend or a chlorinated solvent, and those three need three different answers.

What does a high-propellant, high-flow product change?

Brake cleaner and carburettor cleaner are used in long bursts and empty fast, which pushes towards the larger formats: De 56–66 mm at the tall end of the height range. It also shifts the pressure question onto the can body and the base geometry, and onto the valve and actuator, which are your components. Dimethyl ether as a propellant is common in this sector and behaves differently from a hydrocarbon — it is a solvent in its own right, so it attacks the lining as well as pressurising the can.

If the propellant is DME, say so. It changes the lining shortlist more than the active does.

Which formats does the sector run?

De 46–55 mm covers the small, high-value items — penetrating oil, thread locker, small tyre dressing. De 56–66 mm carries brake cleaner, carb cleaner, underbody coating and the workshop-size lubricants. Height is chosen by the burst duration the product needs, so this is the sector where the tall end of the 88–240 mm range gets used most.

  • De 46–55 mm — penetrating oil, small lubricants, touch-up and detail products
  • De 56–66 mm — brake and carb cleaner, underbody coating, workshop lubricants
  • De 35–45 mm — rarely used; the fill is too small for the working pattern

What does the label have to do that a consumer label does not?

Carry instructions. An automotive aerosol is a tool, and the buyer reads the can to find out how long to leave it, whether it needs ventilation, and what it must not touch — paint, rubber, sensors, aluminium parts. That is a text block, not a brand block, and it usually means a two-column layout on the back with a large flat colour area for the signal word.

The other requirement is orientation. A workshop stores cans on a shelf, in a tray, or on its side; the base is what touches the surface. Base corrosion from a damp workshop floor is a real failure mode in this sector, and it is decided by the external coating, not by the formulation.

What this sector asks of the can
Requirement Why it matters What we do
Aggressive solvent resistance Acetone, toluene, heptane, chlorinated blends Lining shortlisted per solvent blend; grades on the specification sheet TBC
DME as propellant DME is a solvent, not only a propellant Named in the brief; treated as a formulation component, not a filling detail
Base corrosion A damp workshop floor is the storage condition External base coating specified per project TBC
Long burst duration Brake and carb cleaner empty fast De 56–66 mm at the tall end of H3 88–240 mm
Instruction block The buyer reads the can to use the product Up to 8 colours, full-body print area, layout checked for minimum type size
Valve and actuator performance Spray pattern is part of the product Valve remains your component; crimp matched to your drawing

Question about your spec?

Send the body diameter and the product you are filling. We answer in writing, usually the same working day.

Call +86 138 0518 4203

Where we will say no

Where a formulation is a chlorinated solvent blend at a concentration we cannot line for, the answer is that we cannot line for it — not a thicker coating and a hope. Automotive buyers are technical enough to test, and a failure at the customer's bench is more expensive than a declined enquiry.

EA Packaging makes the container only: we do not fill cans, do not formulate product, and do not issue EAC, ANVISA or ANMAT registrations. What you get is a monobloc aluminium can, De 35–66 mm and H3 88–240 mm, printed in up to 8 colours, with the internal coating matched to the formula you describe and the valve cup at 1″ (25.4 mm) or 20 mm. Both are confirmed in writing before we quote, and we supply the test reports and material declarations your importer files under its own name.

Questions

Questions about automotive aerosols

Can an aluminium can hold acetone-based brake cleaner?

It can, with a lining specified for that solvent system rather than for the product name. “Brake cleaner” covers acetone blends, heptane blends and chlorinated blends, and those need different answers, so the formulation — or at least the solvent list — has to be in the brief. This is also the sector where we most often ask for a sample and a stability check before anything is committed.

Do you supply the valve and the spray nozzle?

No. We form the can and crimp the valve cup to your drawing. On an automotive product the spray pattern and the flow rate are part of what the customer is buying, so those components staying with you — and with whoever already supplies them — is usually an advantage rather than a limitation.

Which size should a workshop product use?

It follows the burst duration. A product used in ten-second bursts, several times per job, wants the larger body: De 56–66 mm at the tall end of the height range. A small touch-up or penetrating oil wants De 46–55 mm. Capacity is derived from diameter and height once those two are chosen, not the other way round.

Not answered above?

Ask the question directly — one line is enough to start.

Call +86 138 0518 4203

Send the specification you have. We will fill the gaps.

Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.

Request a quote Call +86 138 0518 4203

Reply within one working day · GMT+8