Tell us the diameter and what you fill. One line starts a quote.

Quick message

Leave a contact. We reply in writing.

Two fields are enough. If you only know the end product, say that — we will ask for the rest once.

Reply within one working day · GMT+8

Prefer to write directly? +86 138 0518 4203

The decorating line seen from the print unit end

Glossary

The vocabulary of an aerosol can, defined once.

Most specification arguments between a buyer and a can maker are arguments about words. De is not a capacity. C2 is not a volume the can holds. “Burst” is not “deformation”. Each term below has a stable anchor, so a definition can be linked to and quoted on its own.

31 terms · geometry · construction · coatings · print · valve · performance

De · H3 · C2 · Brimful capacity · Headspace · Fill ratio · Monobloc · Impact extrusion · Slug · Trimming · Necking · Flanging and curling · Shoulder profile · Dome · Concave base · Wall thickness · Internal lining · Base coat · Passivation layer · Amphoteric · Dry offset printing · Trapping · Minimum line weight · White basecoat · Over-lacquer (overvarnish) · Valve cup (mounting cup) · Crimp dimensions · 1″ valve (25.4 mm) · 20 mm valve · Actuator · Dip tube · Propellant · Bag-on-valve (BOV) · Burst pressure · Deformation pressure · Shelf life

Geometry — how a can is specified

De — body diameter

The external diameter of the cylindrical body, in millimetres. It is the first half of the specification, because it fixes the tooling, the print cylinder circumference and the pallet pattern. De is stated as a nominal figure; the tolerance is on the drawing, not on the designation.

H3 — can height

The overall height of the finished can body, base to top, excluding valve and cap. It is the second half of the specification: together with De it fixes the internal volume, the fill, the carton and the freight. The exact reference plane used for measurement is confirmed on the drawing for each size, because a height without a datum is not a number.

C2 — nominal capacity

The nominal fill volume a size is designated by, not the volume the can physically holds. A 300 ml can does not contain exactly 300 ml of internal space. C2 is a designation used for ordering and labelling, which is why the range on this site is organised by De × H3 and the capacity follows from it.

Brimful capacity

The total internal volume of the can measured to the brim, with no valve fitted. It is the physical upper bound, always larger than the nominal capacity, and it is one of the numbers a filling line needs in order to set a fill height and a headspace.

Headspace

The volume left empty above the product, which the propellant and the product's own vapour occupy. It is set by the filler, not by the can, but the can's internal height is what limits it — which is why the usable internal height is confirmed per size rather than inferred from H3.

Fill ratio

Product volume divided by brimful capacity. A high fill ratio means less headspace and a more efficient pack, but it leaves less room for expansion and for the propellant, so it is a filling decision with a pressure consequence.

Construction and process

Monobloc

A can formed as a single piece of metal: wall, shoulder and base continuous, with no side seam and no seamed ends. Every can on this site is monobloc. The alternative constructions are three-piece (welded body plus two seamed ends) and two-piece drawn (drawn body with one seamed end).

Impact extrusion

The process that produces a monobloc body. An aluminium slug is struck by a punch inside a die and the metal flows up around the punch into a seamless tube. The base is closed by the process itself, which is why there is no bottom seam to fail.

Slug

The blank from which an impact-extruded body is formed: a flat, round disc of aluminium cut from strip, of a defined alloy and temper. Slug quality — alloy, grain, surface — determines how evenly the wall thins, so it is a material decision rather than a purchasing detail.

Trimming

Cutting the extruded tube to the finished can height (H3). It is where the second specification number is physically set, and where the edge that later becomes the flange is created.

Necking

Reducing the diameter of the open end so that the valve cup can be seated. A necked can uses a smaller cup than its body diameter, which is why a De 66 mm body can still take the same 1″ valve as a De 45 mm body.

Flanging and curling

Forming the rim at the open end — the surface the valve cup seats against and the crimp closes onto. Flange geometry is part of the seal, so it is specified together with the valve cup rather than separately.

Shoulder profile

The curve between the body and the neck — how high it rises and how tight the radius is. It is what the eye reads as the can's silhouette, and what the upper row of a pallet rests on. Two cans with the same body diameter and the same overall height can look like different products because of this curve alone, which is why it is drawn and agreed rather than described. Drawings usually name the shape rather than the curve — round, flat, bullet, concave shoulder — and those names are not standardised between plants, so the sample is the agreement and the word is only a label.

Dome — the closed bottom of the can

The curved closed end at the bottom of the can — the end the impact-extrusion punch leaves closed, not the top. In can-making the word is bottom-side throughout: a two-piece can is a body with its dome drawn in the same piece, closed at the bottom and open at the top, and the dome reversal and dome growth measurements a technical buyer asks for are taken on this surface. It is closed by the impact-extrusion punch itself, with no seam, which is why there is nothing at the bottom to fail. Its job is pressure first: a curved end carries internal pressure in tension rather than bending a flat plate, and when the pressure is exceeded it is the dome that moves — the base domes out before the can bursts (see deformation pressure). It is also the surface the can stands on, so the same curvature is a standing decision as well as a pressure one, and its depth and radii are set on the drawing (see concave base).

The top of a monobloc aerosol can has no dome, and that is worth stating plainly. The structure runs one way — body → shoulder → neck → curl → valve cup — and the valve cup is the closure. A can formed in one piece has no separate end cap, so there is no second curved end to specify, print or measure. The curved surface above the body is the shoulder, and it is drawn as its own curve (see shoulder profile).

Concave base — the geometry of the dome

The base is not flat, and the direction of the curvature is a specification rather than a detail. Concave — domed inward, away from the product — is the normal choice for a pressurised can: the curved end carries the pressure as membrane tension, it is stiffer against the deformation that precedes a burst, and it leaves a defined standing ring at the outer edge instead of a full disc. A convex base is a different selection and a different product position, so it is not inferred from the word “dome”. What the drawing has to carry, and what is therefore agreed rather than described: the depth of the dome, the radius at its centre and the radius at the transition into the wall, and the width and position of the standing ring. None of it is visible in a product photograph and all of it is decided by pressure and by the filling line — which is why it belongs here as parameters and not in the entry above as a definition (see dome for what the surface is, and deformation pressure for the measurement that tests it).

Wall thickness

The thickness of the extruded can wall. It is set by the impact-extrusion process and trimmed to the drawing; it is not the same as the thickness of the base or the shoulder, and it is not a single number across the can. It is a pressure decision before it is a cost decision: the wall is what holds the can against internal pressure, which is why it is read together with burst pressure and deformation pressure rather than assumed from the drawing.

Coatings — the layer that decides the shelf life

Internal lining

The coating applied to the inside of the can to separate the aluminium from the formulation. It is selected against the formulation — carrier, pH, aggressive components — and it is the single decision that cannot be reversed once the cans are made. The grades available to a plant are named on its specification sheet.

Base coat

The external coating the print sits on. It provides the background colour — white, or a tinted base — and it changes every colour printed over it, which is why a colour target is agreed on a sample rather than from a Pantone number alone.

Passivation layer

The thin, self-forming oxide layer on aluminium that makes the metal behave as it does in air. It is why aluminium does not rust like steel, and also why it is not inert: the same layer dissolves in strong acid and in strong alkali.

Amphoteric

A material that reacts with both acids and bases. Aluminium is amphoteric, which is the single most useful thing to know when judging whether a formulation belongs in an aluminium can. It is why an acidic or a caustic fill is a lining question, and sometimes a different-container question.

Print

Dry offset printing

The printing process used on a formed aerosol can. Ink is transferred from a plate to a blanket and then onto the curved body, without water in the process — hence “dry”. It prints onto a cylinder rather than a flat sheet, which is why artwork behaves differently from a litho proof.

Trapping

A deliberate overlap between two adjacent printed colours, so that a small misregistration does not leave a hairline of unprinted substrate between them. Trapping values depend on the colour sequence and on the substrate, so they are set per artwork rather than applied as a constant.

Minimum line weight

The thinnest line that will print reliably at a given size on a given substrate. Below it a fine rule breaks up or fills in. It exists on every printing process and it is the first thing checked when a design is prepared for a flat sheet rather than for a curved can.

White basecoat

A white layer printed under the design so that colours sit on white rather than on bare aluminium. It makes colours predictable and it costs a print station. Without it, the metal shows through and the result depends on the alloy and the lighting.

Over-lacquer (overvarnish)

The clear coat printed over the decoration to protect it — also called overvarnish. It sets the finish (gloss, matt, or a mix of the two) and it takes the abrasion a can meets in a carton, on a shelf and in a bathroom cabinet. A gloss over-lacquer deepens the colours underneath it; a matt one softens them. That is a design decision, not a defect in the print.

Valve and dispensing

Valve cup (mounting cup)

The metal cup that holds the valve and is crimped onto the can flange. It is the joint between the can and the dispensing system, and it is the only part of the valve assembly that belongs to the can maker.

Crimp dimensions

The set of diameters and the crimp height that seal the valve cup onto the flange. They are matched to the valve drawing, not to a catalogue number, because a crimp that is right for one valve will leak on another. This is why the valve stays with the buyer.

1″ valve (25.4 mm)

The standard aerosol valve interface, 25.4 mm across the cup. It covers personal care, household and most technical aerosols, and it is one of the two interfaces fitted on this site.

20 mm valve

A compact valve interface, 20 mm across the cup, normally used on smaller body diameters and on products with a low delivery rate. It is the second of the two interfaces fitted here — not the beverage-can end, which is a different family entirely.

Actuator

The button or cap that the user presses, which opens the valve and shapes the spray. It sets the spray pattern and the delivery rate, so it is part of the product's performance and belongs to the buyer, not to the can maker.

Dip tube

The tube that carries product from the bottom of the can up to the valve, so the can works upright. Its length is matched to the internal height, and its absence — a valve without a tube — is what makes a can work in any orientation.

Propellant

The compressed or liquefied gas that drives the product out. Hydrocarbons and dimethyl ether are common; DME matters for the can because it is also a solvent, so it attacks the lining as well as pressurising the can. Nitrogen, being inert, does not.

Bag-on-valve (BOV)

A system in which the product sits in a bag inside the can and the propellant sits outside it, so product and propellant never mix. It suits gels, creams and products that must not be exposed to air — but it is a different package from the plain aerosol can described on this site.

Performance

Burst pressure

The internal pressure at which the can fails structurally. It is measured per size and construction, and it is the number a technical buyer asks for first. For this plant it is being requested as a test report and is marked open rather than estimated.

Deformation pressure

The internal pressure at which the can starts to deform permanently — the base domes out, typically — before it bursts. It sits below the burst pressure and above the working pressure, and together with burst it defines the safety margin of the pack.

Shelf life

The period over which a filled can remains fit for use. It is decided by the interaction of the formulation with the lining, not by the can alone, which is why a shelf-life claim belongs to the brand and a lining recommendation belongs to the can maker.

Question about your spec?

Send the body diameter and the product you are filling. We answer in writing, usually the same working day.

Call +86 138 0518 4203

Send the specification you have. We will fill the gaps.

Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.

Request a quote Call +86 138 0518 4203

Reply within one working day · GMT+8