Tell us the diameter and what you fill. One line starts a quote.

Quick message

Leave a contact. We reply in writing.

Two fields are enough. If you only know the end product, say that — we will ask for the rest once.

Reply within one working day · GMT+8

Prefer to write directly? +86 138 0518 4203

The printing rollers and blanket of the decorating unit

Compare

Aluminium against tinplate, including the part where tinplate wins.

We make aluminium aerosol cans and only aluminium ones, so this page has an obvious conflict of interest. It is written anyway, because a buyer who discovers the trade-offs after ordering is a lost account, and because half of the arguments used to sell aluminium against tinplate do not survive contact with a technical department.

Construction · weight · corrosion · print · tooling

What is actually different about the two cans?

They are made by different processes, and that single difference produces almost every other difference on this page. An aluminium aerosol can is a monobloc: a slug of aluminium is impact-extruded into a seamless tube, so the wall, the shoulder and the base come out of one piece of metal. A three-piece tinplate can is made from flat steel sheet — a body rolled and welded along a longitudinal seam, a top and a bottom seamed on. A two-piece tinplate can is drawn from flat sheet into a cup, which removes the body seam but keeps a seamed end.

So the honest summary is one sentence: aluminium buys you the absence of a seam, and you pay for it in metal cost and in tooling. Everything else follows.

The two constructions, side by side
Attribute Aluminium monobloc Three-piece tinplate
Body seam None — wall, shoulder and base in one piece Longitudinal weld, plus seamed top and bottom
Material density About 2.70 g/cm³ About 7.85 g/cm³ for the steel substrate
Corrosion at a breach Pitting of the aluminium itself Red rust once the tin coating is broken through to steel
How the body is printed Dry offset on the formed can Offset lithography on flat sheet, then formed
Effect of changing size New extrusion tooling New body blank and seaming setup
Typical best fit Aerosols, seamless cosmetic and technical packs Large volumes of standard sizes, and products needing a steel barrier
Recycling High-value scrap stream, widely recycled Magnetic separation, widely recycled

Question about your spec?

Send the body diameter and the product you are filling. We answer in writing, usually the same working day.

Call +86 138 0518 4203

Why does the absence of a seam matter so much?

Because a seam is a discontinuity, and a discontinuity is where corrosion starts. On a welded tinplate body the weld and the two seamed ends are the places where the protective coating is thinnest or interrupted, and a solvent-borne or water-borne formulation will find them given months on a shelf. On a monobloc aluminium body there is no such line, so the corrosion risk concentrates entirely in the quality of the internal lining — which is a process you can control, rather than a joint you have to trust.

That is the real argument for aluminium in personal care, in automotive and in any product with an aggressive carrier. It is not that aluminium does not corrode; it is that the failure has one cause instead of three.

Why is aluminium more expensive per can?

Two reasons, and neither is a markup. First, the metal: aluminium as a raw material costs more per kilogram than steel sheet, and although a monobloc can uses less metal for the same volume because it is lighter, the two effects only partly cancel. Second, the tooling: impact extrusion needs a punch and a die per body diameter, and a change of diameter means new tooling, whereas a tinplate body change is a change of blank and seam setup. That is why aluminium becomes economic at a certain order size and awkward below it — and why a supplier who quotes a small aluminium run cheaply is usually cutting something else.

There is a third, quieter reason: printing on the formed can. Dry offset onto a curved aluminium tube is a more demanding process than lithography on flat sheet, and the artwork has to be prepared for it.

Where is tinplate actually the better answer?

Three situations, and they are not rare.

  • Very large volumes of a standard size, where the tinplate tooling cost is amortised into nothing and the material saving dominates
  • Products that need a steel barrier or a genuinely long ambient shelf life with an aggressive fill, where a proven tinplate pack already exists and passes
  • Filling lines and markets already set up around tinplate dimensions, where changing the can means changing the line

A fourth case is honest to add: where the buyer's volume sits below what aluminium tooling can absorb. We would rather say that at the enquiry than quote a number that cannot be held.

What about weight and freight?

Aluminium is roughly a third of the density of steel, and an empty can is mostly air, so the per-can weight difference is smaller than the density figures suggest. Where it does matter is on a full container: an empty-can shipment is charged on volume rather than weight for both materials, so the saving appears mainly in the filled-goods freight and in the handling ergonomics on a filling line, not in the inbound container.

Both materials are recycled at high rates and both have established scrap value. A sustainability argument that claims one is recyclable and the other is not is not a serious argument.

So how do we recommend a buyer decide?

Start from the formulation and the market, not from the material. If the fill is aggressive, the shelf life long and the pack has to look premium at close range, aluminium removes a class of failure. If the volume is large, the size standard and the fill benign, tinplate is likely cheaper and there is no reason to pay for a seam you do not need. If the answer is genuinely unclear, we will say so — and where we are not the right supplier, saying it at the enquiry stage costs us one order and saves both sides a project.

Questions

Questions about the comparison

Is an aluminium can stronger than a tinplate can?

Not in a way that can be stated as a single answer. A monobloc aluminium body has no seam to fail, which is a real advantage under internal pressure and under an aggressive fill. A steel body has higher intrinsic strength for the same wall thickness. What decides a specification is the burst and deformation behaviour of the finished can against the fill and the transport conditions — and that is measured per size, not argued per material.

Can an aluminium can hold an acidic product?

Aluminium is amphoteric: it is attacked by strong acid and by strong alkali, and it relies on an internal lining to separate it from the product. An acidic fill is therefore a lining question rather than a material question, and it needs a lining specified for that pH band. Where the pH sits far outside the comfortable range, the honest answer may be that another container is the better choice.

Do you make tinplate cans as well?

No. Aluminium is the product, which is why the tooling, the coatings and the print process are built around one-piece aluminium bodies. If a three-piece tinplate can fits your volume better, we will say so — this page exists partly so that conversation can happen early rather than after a quotation.

Not answered above?

Ask the question directly — one line is enough to start.

Call +86 138 0518 4203

Send the specification you have. We will fill the gaps.

Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.

Request a quote Call +86 138 0518 4203

Reply within one working day · GMT+8