Tell us the diameter and what you fill. One line starts a quote.

Quick message

Leave a contact. We reply in writing.

Two fields are enough. If you only know the end product, say that — we will ask for the rest once.

Reply within one working day · GMT+8

Prefer to write directly? +86 138 0518 4203

A finished printed aluminium aerosol can held in a gloved hand

Applications · Personal care

Personal care is the sector where the can has to look as good as it works.

Deodorant, antiperspirant, body spray, dry shampoo, shaving foam, hairspray. These are the fills that put the can in someone's hand at close range, on a wet bathroom shelf, for months at a time. The specification has two jobs at once: hold an alcohol-heavy formulation without corroding, and carry print fine enough to survive being looked at.

De 35–45 mm · 8 colours · 20 mm or 1″ valve

What actually goes wrong with a personal care can?

Two failures account for most of it, and neither shows up in the first month. The first is corrosion at the base and at the shoulder: an ethanol-based fill attacks the aluminium wherever the internal lining is thin, and the failure appears as a pinhole six or nine months into shelf life rather than on the filling line. The second is print that looked correct on a flat proof and reads soft on a curved body — fine serif type, thin reverses, and tight registration between two dark colours are where it shows first.

Both are settled long before production. The lining is chosen against the formulation, and the artwork is checked against the print process before a cylinder is cut.

Which formulations are the difficult ones?

Anhydrous ethanol systems are the most common and the least forgiving: the alcohol carries the active and also carries it into any discontinuity in the lining. Antiperspirants add aluminium chlorohydrate or aluminium zirconium salts, which are aggressive in their own right and are usually the reason a can that worked for a deodorant fails for an antiperspirant. Silicone-heavy and propylene-glycol-heavy formulations behave differently again — kinder to the lining, harder to atomise, which pushes the question towards the valve rather than the can.

We ask for the formulation, or at least its carrier and its pH, before recommending a lining. Without it, the recommendation is a guess dressed up as advice.

Which body diameter does this sector use?

De 35–45 mm carries most of it. A deodorant is held and operated in one hand, so the body stays narrow and the height does the work of setting the fill volume. Wider bodies appear in family-size body spray and in shaving foam, where the can stands on a shelf instead of being gripped.

  • De 35–45 mm — deodorant, antiperspirant, body spray, dry shampoo
  • De 46–55 mm — shaving foam and gel, larger body spray, hairspray
  • De 56–66 mm — rarely used here; at that width the format stops being hand-held

What does the print have to do that other sectors do not?

This is the highest standard of the seven sectors, and the reason is proximity. A buyer reads this can at 30 cm, compares it against the one beside it on the shelf, and judges the brand on the registration of a one-millimetre line. Two things follow: up to eight colours applied to the formed can rather than to flat sheet, and artwork checked against the process before sampling — minimum line weight, trapping between adjacent colours, and whether a fine reverse will fill in on a curved aluminium surface.

Metallic effects and matte or gloss varnishes are a print decision rather than a can decision, and they are quoted per project.

What this sector asks of the can
Requirement Why it matters What we do
Alcohol resistance Ethanol and antiperspirant salts find any discontinuity in the lining Lining selected against the formulation; grades named on the specification sheet TBC
No side seam A welded seam is the first place a solvent reaches bare metal Monobloc body — wall, shoulder and base in one piece
Print fidelity The can is read at arm's length, next to its competitors Up to 8 colours on the formed body; artwork checked before the cylinder is cut
Hand-held diameter The user grips the body, not the cap De 35–45 mm covers the sector; 46–55 mm for foam and family sizes
Valve continuity Brands already run a valve and a filling line Crimp matched to your valve drawing; the valve itself is outside our scope
Base corrosion in a wet room A bathroom stays humid for years External base lacquer specified per project TBC

Question about your spec?

Send the body diameter and the product you are filling. We answer in writing, usually the same working day.

Call +86 138 0518 4203

What is outside our scope, and why does that matter here?

The valve, the actuator and the cap. We form the can and crimp the valve cup to the component you specify, so a brand that already runs a valve keeps its filling line unchanged. The boundary is deliberate: responsibility for a leaking valve stays with the valve maker, and responsibility for the can stays with us. On a sector where a single-figure unit cost is decided by a component nobody photographs, that clarity is worth more than a wider offer.

Ask for the lining recommendation in writing, with the formulation attached. It is the one decision on this page that cannot be reversed once the cans are made.

EA Packaging makes the container only: we do not fill cans, do not formulate product, and do not issue EAC, ANVISA or ANMAT registrations. What you get is a monobloc aluminium can, De 35–66 mm and H3 88–240 mm, printed in up to 8 colours, with the internal coating matched to the formula you describe and the valve cup at 1″ (25.4 mm) or 20 mm. Both are confirmed in writing before we quote, and we supply the test reports and material declarations your importer files under its own name.

Questions

Questions about personal care

Does aluminium work for an antiperspirant, or do I need tinplate?

Aluminium works, but the lining has to be chosen for the formulation rather than for the sector. Antiperspirant actives are more aggressive than a plain deodorant and are the usual reason a specification that passed for one fails for the other. Send the formulation, or at least its carrier and pH, and the lining recommendation follows from it. Where a brand already has a tinplate can that passes, the honest answer may be to keep running it.

Do you supply the valve, the actuator and the cap?

No. The can and the crimped valve cup are ours; the valve, actuator and cap are yours or your component supplier's. We crimp to your valve drawing so nothing on the filling line changes. Keeping that boundary is what makes responsibility for a leak unambiguous.

Can you match a Pantone colour on a curved aluminium body?

We print to a colour target agreed at sampling, not to a Pantone number in isolation, because an aluminium substrate with a clear or white basecoat shifts the result and a curved surface changes ink laydown. The approved sample is the reference for production. If a brief insists on a Pantone value with no substrate-adjusted target, settle that at sampling rather than at the print run.

Not answered above?

Ask the question directly — one line is enough to start.

Call +86 138 0518 4203

Send the specification you have. We will fill the gaps.

Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.

Request a quote Call +86 138 0518 4203

Reply within one working day · GMT+8