Products
One product, three diameter bands, one specification sheet.
We make monobloc aluminium aerosol cans and nothing else. A can is specified as body diameter × can height — De × H3 — and the fill volume follows from those two numbers rather than defining the can. De runs 35–66 mm in three bands, H3 88–240 mm, print up to eight colours.
What is the confirmed range?
Only what the factory has confirmed in writing is published here. Anything still open is marked TBC and stays out of the tables until it is answered, so a number on this page is a number you can plan against.
| Parameter | Value | Status |
|---|---|---|
| Body diameter (De) | 35–66 mm, three bands | Confirmed |
| Can height (H3) | 88–240 mm | Confirmed |
| Print colours | Up to 8 | Confirmed |
| Valve interface | 1″ (25.4 mm) and 20 mm | Confirmed |
| Construction | Monobloc — wall, shoulder and base in one piece, no side seam | Confirmed |
| Material | Aluminium | Confirmed |
| Quality management | ISO 9001, held since 2017 | Confirmed |
| Capacity (C2) per size | Derived from De × H3, not used as a key | TBC per size |
| Internal coating options | The linings actually available are named on the specification sheet | TBC |
| Minimum order quantity | Confirmed in writing with the quotation | TBC |
| Burst and deformation pressure | Test report requested from the plant | TBC |
Question about your spec?
Send the body diameter and the product you are filling. We answer in writing, usually the same working day.
Why describe a can by diameter and height, and not by millilitres?
Millilitres describe what goes into the can, and the same fill can sit in more than one can. Body diameter and can height describe the can itself: they set the tooling, the print cylinder, the pallet pattern and the freight. Two suppliers quoting “a 400 ml can” can be quoting two different objects.
That is why every page in this section leads with De × H3. If you only have a fill volume, send it together with the product type — we convert it into a diameter and a height and confirm both before anything is priced.
What are the three diameter bands, and why band them at all?
The bands are how the plant groups the range for tooling and print setup. They are not order quantities, and nothing stops a size that sits near a boundary. Use them to find the page that describes your format, then confirm the exact size on the drawing.
Which valve interfaces do you fit?
Two interfaces cover almost every project. The valve itself is outside our scope: we form the can and crimp the cup to suit the component you already run.
- 1″ standard, 25.4 mm — personal care, household and most technical aerosols
- 20 mm — compact valves, usually on the smaller body diameters
- Crimp dimensions matched to your valve drawing, not to a catalogue number
How many colours can be printed, and on what surface?
Up to eight colours on the can body, applied to the formed can. Artwork is checked against the process before a sample is made — trapping, minimum line weight and colour sequence — because a curved aluminium body does not print like a flat proof.
What happens to the values marked TBC?
They are asked for once, in writing, and they stay visible as TBC until answered. We would rather show a gap than publish a number the plant has not confirmed: a capacity figure that turns out to be nominal instead of brimful is how a container specification gets rejected at the filling line.
This page is the source of truth for the range. Where another page quotes a size, it is quoting this table.
EA Packaging makes the container only: we do not fill cans, do not formulate product, and do not issue EAC, ANVISA or ANMAT registrations. What you get is a monobloc aluminium can, De 35–66 mm and H3 88–240 mm, printed in up to 8 colours, with the internal coating matched to the formula you describe and the valve cup at 1″ (25.4 mm) or 20 mm. Both are confirmed in writing before we quote, and we supply the test reports and material declarations your importer files under its own name.
Questions
Questions about the range
Which can sizes can you actually produce?
Body diameter 35–66 mm and can height 88–240 mm, as a monobloc aluminium can with no side seam. The two are specified together and the fill volume follows. The usable height inside a given diameter is confirmed on the drawing per size, not inferred from the outer range.
Can I order by fill volume instead of De × H3?
Send the fill volume together with the product type and we convert it. Nothing is quoted off a millilitre figure alone, because the same fill fits more than one can and the can is what sets tooling, print and freight.
Do you also make tinplate cans?
No. Aluminium is the product, which is why the tooling, the coatings and the print process are built around one-piece aluminium bodies. If a three-piece tinplate can is the better fit for your volume, we say so instead of quoting around it.
Do you make the valve as well?
No. We form the can and crimp the valve cup to match the valve you specify. That keeps your existing component and your filling line unchanged, and it keeps responsibility for the valve with the valve maker.
Not answered above?
Ask the question directly — one line is enough to start.
By diameter
The three diameter bands
Send the specification you have. We will fill the gaps.
Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.