Tell us the diameter and what you fill. One line starts a quote.

Quick message

Leave a contact. We reply in writing.

Two fields are enough. If you only know the end product, say that — we will ask for the rest once.

Reply within one working day · GMT+8

Prefer to write directly? +86 138 0518 4203

Close view of the print unit, where the ink meets the can body

FAQ

Every question we get asked, including the awkward ones.

Grouped by what a buyer is trying to decide. Where the answer is a number the factory has not confirmed, the answer says so and points at the document that will carry it — because an FAQ that invents a lead time is worse than an FAQ that admits one is still open.

Range · valves · linings · print · ordering · certificates

Sizes · Ordering by volume · Valve interface · Components · Internal lining · Water-based fills · Print colours · Artwork · MOQ · Lead time · Mould cost · Tinplate · What we do not make · ISO 9001 · Pressure data · Factory or trader · What to send

The range

A can is specified as body diameter × can height. Everything else follows from those two numbers, which is why the questions about size are really questions about those two figures.

Valves and components

Two interfaces, and a boundary that runs through the middle of the assembly. The can and the crimped cup are ours; everything above the cup belongs to you or to your component supplier.

Linings and formulations

The lining is the one decision that cannot be reversed after the cans are made, so it is the one we ask most about — and the one we will not recommend from a product description alone.

Printing and artwork

Eight colours, dry offset on the formed body, and artwork checked against the process before a cylinder is cut. The detail lives on the print guide, so this section only answers what is asked most.

Ordering and commercial terms

The three questions every buyer asks first are the three we cannot answer from a web page: minimum quantity, tooling cost and lead time. They are confirmed in writing with the quotation for the specific size and decoration, because they depend on both.

Certificates and compliance

ISO 9001, in force since 2017, and a page that lists everything else by status rather than by logo.

Question about your spec?

Send the body diameter and the product you are filling. We answer in writing, usually the same working day.

Call +86 138 0518 4203

Answers

All questions

What sizes can you make?

Body diameter 35–66 mm in three bands, can height 88–240 mm, as a monobloc aluminium can with no side seam. The two are specified together: the fill volume follows from diameter and height rather than defining the can. The usable internal height for a given diameter is confirmed on the drawing per size, not inferred from the outer range.

Can I order by millilitres instead of by diameter and height?

Send the fill volume together with the product type and we convert it into a diameter and a height, then confirm both before anything is priced. Nothing is quoted from a millilitre figure alone, because the same fill fits more than one can and the can is what sets tooling, print and freight.

Which valve interfaces do you fit?

1″ standard (25.4 mm) and 20 mm. The crimp dimensions are matched to your valve drawing rather than to a catalogue number, so an existing valve keeps working and the filling line does not change. The valve itself is outside our scope.

Do you supply the valve, actuator and cap?

No. We form the can and crimp the cup to your component. That keeps responsibility for a leaking valve with the valve maker and responsibility for the can with us, which is worth more on a technical project than a wider offer would be.

How do you decide which internal lining to use?

From the formulation — at minimum its carrier and its pH, plus any aggressive component such as a chlorinated solvent or DEET. The lining is chosen against that, not against the product category, because “a deodorant” and “an antiperspirant” can need different answers. The specific grades available to this plant are named on the specification sheet.

Can an aluminium can hold a water-based or alkaline product?

Yes, with a lining specified for that pH band. Aluminium is amphoteric — attacked by strong acid and strong alkali alike — so a water-based or caustic fill is a lining and base-geometry question. Where the pH sits far outside the comfortable range, the honest recommendation may be a different container.

Will my artwork print the way it looks on screen?

Not identically, and the differences are predictable: trapping set for the colour sequence, a minimum line weight below which a fine rule breaks up, thin reverses that can fill in, and a base colour — bright aluminium or white basecoat — that shifts every colour printed over it. That is why artwork is checked against the process before a cylinder is cut, which is also the cheapest moment to change it.

What is the minimum order quantity?

It is confirmed in writing with the quotation, for the specific size and decoration, and is marked TBC on this site rather than estimated. MOQ depends on the diameter (tooling) and on the number of colours (cylinder), so a single advertised figure would be wrong for most projects.

What is the lead time?

Also confirmed with the quotation, and for the same reason: a repeat size with existing artwork and a new diameter with a new cylinder are not the same project. We will not publish a number that a first order cannot meet.

How much does a mould cost?

Whether new tooling is needed depends on your diameter. If it matches a mould we already run, we say so in writing, together with any tooling charge that applies; if it does not, a new mould is required. Which case applies to you is confirmed per diameter before you commit, along with the cost of the tool and the time to make it. We do not publish a figure, because a mould is priced per diameter and per neck specification, and one number would be wrong for most projects.

Do you make tinplate cans as well?

No. Aluminium is the product, which is why tooling, coatings and print are built around one-piece aluminium bodies. If a three-piece tinplate can fits your volume better, the comparison page says so plainly, including the cases where tinplate wins.

Do you make pharmaceutical aerosols or medical devices?

No. Not pharmaceutical aerosols, not medical devices, not wound-care or disinfectant sprays, not OTC drug products. The factory makes cans for cosmetic and technical products. A product whose claims put it in the medicinal category is outside our scope.

Which certificate do you hold?

ISO 9001, in force since 2017, covering quality management of the manufacturing operation. A PDF copy is supplied with the quotation. Other certificates — environmental, occupational health, food safety, social audit — are not claimed on this site; the certifications page lists them by status rather than by logo.

Can you supply burst and deformation pressure data?

The test report has been requested from the plant and is marked open on this site until it arrives. We will not publish an estimate: on a technical project that figure enters a vendor file and becomes contractual.

Are you a factory or a trading company?

A factory. The can is extruded, lined and printed here as one continuous chain — the sequence is set out step by step — which is what makes it possible to trace a defect to a process step rather than to a shipment. The valve, actuator, cap and filling operation are not made here, and that boundary is stated on every page.

What do you need in order to quote?

Body diameter, can height and valve interface are enough to start. After that: the formulation or at least its carrier and pH, the print requirement, the destination market, and the annual volume. Anything missing is asked for once, in writing, rather than assumed.

Not answered above?

Ask the question directly — one line is enough to start.

Call +86 138 0518 4203

Send the specification you have. We will fill the gaps.

Body diameter, can height and valve interface are enough to start. Anything you do not have yet we ask for once, in writing.

Request a quote Call +86 138 0518 4203

Reply within one working day · GMT+8